Chest · Horizontal push
Barbell Pin Press
The barbell pin press is a bench press where the bar starts each rep from a dead stop on safety pins in a rack. You press it up to lockout, then lower it back down to rest on the pins. Starting without the stretch reflex builds raw pressing strength in the upper range and trains the chest and triceps.
Also known as: Pin press, Bench press from pins, Dead-stop bench press
- Muscle group
- Chest
- Movement pattern
- Horizontal push
- Type
- Compound
- Equipment
- Barbell, Rack, Bench
- Difficulty
- Intermediate
What muscles does the barbell pin press work?
Primary movers
- Pectoralis major (sternal)
- Triceps brachii
Assisting muscles
- Pectoralis major (clavicular)
- Anterior deltoid
- Forearm flexors
- Serratus anterior
The pectoralis major and triceps do the work. The triceps are especially important because the pins limit the range to the upper half of the press.
The front deltoids and upper chest assist, and your forearms grip the bar.
The dead stop removes the bounce and the stretch from the bottom. You have to produce force from nothing, which trains the muscles and nervous system to start a press from a stall.
The benefit is strength in your sticking point. Set the pins where you tend to slow down, and you train that part of the lift directly.
How to do the barbell pin press
Setup
- 1
Set a flat bench inside a rack and place the pins a few inches above your chest.
- 2
Lie on the bench under the bar resting on the pins.
- 3
Grip the bar slightly wider than shoulder-width.
- 4
Pull your shoulder blades back and plant your feet.
Execution
- 1
Brace and press the bar from the pins up to lockout.
- 2
Lower it back onto the pins under control.
- 3
Let it settle fully before the next rep.
- 4
Repeat for the planned number of reps.
Common barbell pin press mistakes
Bouncing the bar off the pins
A bounce brings back the stretch reflex and defeats the purpose.
The fix: Let the bar rest, then reset your brace before pressing.
Setting the pins too low
The press becomes a full bench press with a pause.
The fix: Set the pins at your sticking point, not at your chest.
Lifting the hips off the bench
It changes the press and may strain the lower back.
The fix: Keep your hips on the bench and your feet planted.
Losing tightness on the pins
A loose upper back makes the press unstable.
The fix: Keep your shoulder blades pulled back as you rest.
How many sets and reps?
| Goal | Sets | Reps | Load | Rest |
|---|---|---|---|---|
| Strength | 4–5 | 3–5 | Heavy, below your bench max | 3–4 min |
| Hypertrophy | 3–4 | 6–8 | Moderate, dead stop | 2 min |
| Beginner | 2–3 | 6–8 | Light, high pins | 2 min |
Use it as a secondary lift after your main bench press. Use a spotter or set safety pins below the bar path.
Running the barbell pin press in your next block? Hercules logs every set, shows last session's numbers before you lift, and suggests when to add weight.
Get it on Google PlayBarbell Pin Press variations and alternatives
Barbell Bench Press
AlternativeThe standard lift with full range.
Close Grip Barbell Bench Press
AlternativePuts more work on the triceps.
A guided bar that needs less balance.
Dumbbell Bench Press
EasierA freer path with lighter weight.
Wide Grip Barbell Bench Press
AlternativeShifts the work more to the chest.
Frequently asked questions
What does the pin press work?
The chest, triceps and front deltoids, mainly in the upper range.
Why press from a dead stop?
It removes the bounce and builds starting strength.
Where should I set the pins?
At your sticking point, where the bar slows during a normal press.
Is a spotter needed?
Yes, or set safeties so the bar cannot trap you.
Hercules tracks every barbell pin press you log, shows you last session's numbers before you lift, and flags when your progress stalls.
Get it on Google Play