Shoulders · Shoulder abduction

Leaning Single Arm Lateral Raise

The Leaning Single Arm Lateral Raise is a shoulder exercise where you hold a support with one hand, lean your body slightly away, and raise a dumbbell out to the side with the other. The lean keeps tension on the side delt at the bottom, where a regular standing lateral raise goes slack.

Also known as: Leaning lateral raise, Lean-away lateral raise, Supported single arm lateral raise, Leaning dumbbell lateral raise

Muscle group
Shoulders
Movement pattern
Shoulder abduction
Type
Isolation
Equipment
Dumbbell, Rack
Difficulty
Intermediate

What muscles does the leaning single arm lateral raise work?

Primary movers

  • Lateral deltoid

Assisting muscles

  • Anterior deltoid
  • Rear deltoid
  • Supraspinatus
  • Upper trapezius
  • Wrist extensors

The lateral deltoid does nearly all of the work. It lifts your arm out to the side and gives the shoulder its width.

The supraspinatus helps start the raise, and the front and rear delts stabilize the arm. The upper traps assist, so keep your shoulder down to limit them.

The lean changes the resistance. In a standing raise the dumbbell hangs by your side and there is almost no load at the bottom. Leaning away makes the weight pull the arm across your body, which keeps the side delt working from the first inch.

A lean of 10 to 20 degrees is enough. The support is for balance, not to hold your body weight.

How to do the leaning single arm lateral raise

Setup

  1. 1

    Stand next to a sturdy support such as a rack, bench or pole.

  2. 2

    Hold the support with your inside hand and keep your arm straight.

  3. 3

    Hold a dumbbell in your outside hand and lean your whole body slightly away from the support.

  4. 4

    Keep your body straight and your feet planted.

Execution

  1. 1

    Raise the dumbbell out to the side with a slight bend in your elbow.

  2. 2

    Lead with your elbow and keep your shoulder down.

  3. 3

    Stop when your arm is about parallel to the floor.

  4. 4

    Lower the dumbbell slowly back to your side.

  5. 5

    Finish your reps, then switch sides.

Common leaning single arm lateral raise mistakes

Leaning too far

The support takes your body weight and you lose balance.

The fix: Use a small lean of about 10 to 20 degrees.

Swinging with the torso

Momentum takes tension off the side delt.

The fix: Use a lighter dumbbell and keep your torso still.

Shrugging the working shoulder

Your upper traps take over the lift.

The fix: Keep your shoulder down and lead with the elbow.

Rushing the lowering

Dropping the weight wastes the best part of the rep.

The fix: Take about two seconds to lower the dumbbell.

How many sets and reps?

GoalSetsRepsLoadRest
Hypertrophy3–410–15Light, controlled60 s
Endurance2–315–20Very light45 s
Beginner2–310–12Light60 s

Use a light dumbbell and treat this as a finisher for the side delts. Do all reps on one arm before switching, and keep every rep slow.

Running the leaning single arm lateral raise in your next block? Hercules logs every set, shows last session's numbers before you lift, and suggests when to add weight.

Get it on Google Play

Leaning Single Arm Lateral Raise variations and alternatives

Standing version with both arms and no lean.

Lying on your side gives tension at the bottom of the lift.

A cable keeps constant tension through the whole raise.

Frequently asked questions

What does the Leaning Single Arm Lateral Raise work?

Mainly the lateral deltoid, the part of the shoulder that adds width.

Why lean away from the support?

It keeps tension on the side delt at the bottom, where a standing lateral raise goes slack.

How far should I lean?

A small lean of 10 to 20 degrees is enough.

How heavy should the dumbbell be?

Light. Pick a weight that lets you raise with no swinging and lower in about two seconds.

Hercules tracks every leaning single arm lateral raise you log, shows you last session's numbers before you lift, and flags when your progress stalls.

Get it on Google Play