Legs · Squat
Single Leg Leg Press
The single leg leg press is a machine exercise where you press the platform with one leg at a time while the other rests. It trains the quads and glutes with less total weight than a two-leg press, and it shows and helps even out strength differences between your legs. It is a stable way to train one leg at a time.
Also known as: One leg leg press, Unilateral leg press, Single-leg press
- Muscle group
- Legs
- Movement pattern
- Squat
- Type
- Compound
- Equipment
- Leg press machine
- Difficulty
- Intermediate
What muscles does the single leg leg press work?
Primary movers
- Quadriceps
- Gluteus maximus
Assisting muscles
- Hamstrings
- Adductor magnus
- Gluteus medius
- Calves
The quadriceps straighten the knee as you push the platform away, and they do most of the work. The gluteus maximus extends the hip, and its contribution grows as you go deeper and place your foot a little higher on the platform.
The hamstrings and adductor magnus assist at the hip, and the calves help push through the foot. The gluteus medius stabilizes the working leg, which matters more here than on a two-leg press because nothing else is holding your pelvis level.
Training one leg at a time exposes differences between your sides. The weaker leg often lowers slower, shakes or cannot match the same range, and you cannot hide it behind the stronger leg. Working both legs equally over time can help even them out.
Compared with the two-leg version, the load is much lower and the stability demand is higher. The seat and pad support your back, so you can push close to your limit with the quads without worrying about balance or the spine as you would in a squat.
How to do the single leg leg press
Setup
- 1
Sit in the leg press with your back and hips flat against the pad.
- 2
Place one foot in the middle of the platform, about shoulder-width from the center line.
- 3
Release the safety handles and let the other leg rest on the floor or tuck it out of the way.
- 4
Start with a weight well under half of your two-leg working weight.
Execution
- 1
Bend your knee under control to lower the platform until it reaches about 90 degrees.
- 2
Keep your knee in line with your toes.
- 3
Keep your hips and lower back pressed into the seat at the bottom.
- 4
Push through your whole foot to press the platform back up.
- 5
Stop just short of locking your knee at the top.
- 6
Finish all reps on one leg, then switch.
Common single leg leg press mistakes
Letting the knee cave inward
The knee drifts toward the midline, which loads the joint and takes work away from the glutes and quads.
The fix: Push your knee out in line with your toes and press through the whole foot. Lower the weight if it keeps collapsing.
Lowering until the hips curl off the seat
When the pelvis rolls up, the lower back rounds under load and the movement loses stability.
The fix: Stop the descent when your lower back is about to lift off the pad. Reduce depth until your hips stay down.
Locking the knee hard at the top
Snapping the knee straight under load puts stress on the joint and rests the muscles.
The fix: Stop just before the knee is straight and keep a slight bend as you start the next rep.
Pushing through the toes
Shifting forward onto the toes moves the strain to the knee and the calf.
The fix: Keep your weight through the mid-foot and heel, and think about pushing the platform away with the whole sole.
How many sets and reps?
| Goal | Sets | Reps | Load | Rest |
|---|---|---|---|---|
| Hypertrophy | 3–4 | 10–15 per leg | Moderate, 1~2 reps in reserve | 90 s |
| Strength | 3–5 | 6–10 per leg | Heavy but controlled, hips stay down | 2–3 min |
| Beginner | 2–3 | 10–12 per leg | Light, partial range if needed | 60–90 s |
Start with well under half your two-leg weight. Do the same reps and load on both sides, starting with your weaker leg, and add weight only when both legs are clean.
Running the single leg leg press in your next block? Hercules logs every set, shows last session's numbers before you lift, and suggests when to add weight.
Get it on Google PlaySingle Leg Leg Press variations and alternatives
Leg Press
EasierUses both legs, so each one carries less and balance is not a concern.
Bodyweight Split Squats
EasierTrains one leg at a time without a machine, with only your own weight.
Single-Leg Calf Press
AlternativeUses the same machine to train just the calf of one leg.
Hack Squat Machine
AlternativeA different machine path that stresses the quads in a more upright pattern.
Trains one leg with a bigger range and a much higher balance demand.
Frequently asked questions
How much weight should I use?
Start with well under half of what you use for the two-leg press. Single-leg work is limited by stability and the weaker leg, not just strength.
Is the single leg press better than the regular leg press?
It is different. It shows side-to-side differences and lets you train each leg on its own, while the regular press lets you load more total weight.
How deep should I go?
To about 90 degrees at the knee, or until your lower back or hips would start to come off the seat, whichever comes first.
Should I do the weaker leg first?
Yes, start with your weaker side and match the reps on your stronger side. This keeps the weaker leg from being left behind.
Hercules tracks every single leg leg press you log, shows you last session's numbers before you lift, and flags when your progress stalls.
Get it on Google Play