Shoulders · Horizontal abduction

Dumbbell Bent-Over Reverse Fly

The dumbbell bent-over reverse fly is a shoulder isolation exercise where you hinge forward and raise two dumbbells out to your sides with slightly bent elbows. It targets the rear deltoids and the upper back muscles that pull your shoulder blades together. Light weights and a steady tempo work best.

Also known as: Bent-over rear delt fly, Dumbbell rear delt fly, Bent-over dumbbell raise

Muscle group
Shoulders
Movement pattern
Horizontal abduction
Type
Isolation
Equipment
Dumbbells
Difficulty
Beginner

What muscles does the dumbbell bent-over reverse fly work?

Primary movers

  • Posterior deltoid

Assisting muscles

  • Rhomboids
  • Middle trapezius
  • Infraspinatus
  • Teres minor
  • Erector spinae

The posterior deltoid is the main muscle. It pulls your upper arms out and back, away from the midline, which is what the movement looks like when the dumbbells lift out to the sides. Most pressing and pulling work trains this part of the shoulder less than the front and side.

The rhomboids and middle trapezius pull your shoulder blades toward your spine to help the arms rise. A brief pause and squeeze at the top brings them into the lift, but do not let them take over by bending your elbows and rowing.

The infraspinatus and teres minor, small rotator cuff muscles on the back of the shoulder blade, help raise the arm and keep the shoulder steady. They also work as your arms rise to shoulder height.

The erector spinae and hamstrings work isometrically to hold your hinged torso in place. Compared with the seated version, standing makes your lower back and legs do more, and compared with a cable version the tension is lowest at the bottom and highest at the top.

How to do the dumbbell bent-over reverse fly

Setup

  1. 1

    Stand holding a dumbbell in each hand with your feet about hip-width apart.

  2. 2

    Hinge at the hips with soft knees until your torso is close to parallel with the floor.

  3. 3

    Let the dumbbells hang under your chest with your palms facing each other.

  4. 4

    Keep your back flat and your neck in line with your spine.

Execution

  1. 1

    Keep a slight bend in your elbows and hold it in place.

  2. 2

    Lead with the backs of your hands and raise the dumbbells out to the sides.

  3. 3

    Lift until your arms are level with your shoulders.

  4. 4

    Pause at the top and squeeze your rear delts.

  5. 5

    Lower the dumbbells slowly back under your chest.

  6. 6

    Repeat for the desired number of reps without rising up.

Common dumbbell bent-over reverse fly mistakes

Rising up as you lift

Standing up with each rep adds momentum and takes the work off the rear delts.

The fix: Hold your hinge position and keep your torso still for the whole set.

Swinging the weights

Momentum lifts the dumbbells for you and cuts the tension on the muscle.

The fix: Use lighter dumbbells and lower them under control.

Bending the elbows into a row

Pulling the elbows back turns it into a row and brings in the lats and biceps.

The fix: Keep the same soft elbow angle and think of pushing the weights out wide.

Rounding the back

A rounded back puts the strain on your spine and limits your range.

The fix: Push your hips back, brace your core and keep your chest open.

How many sets and reps?

GoalSetsRepsLoadRest
Hypertrophy3–412–20Light, 1–2 reps in reserve45–60 s
Strength3–48–12Moderate, strict form60–90 s
Beginner2–310–15Very light, full control60 s

Use the reverse fly as a shoulder or back accessory after your main presses and rows. Start light, because the rear delts are small, and add reps before adding weight. If the weights feel heavy, the exercise usually turns into a row.

Running the dumbbell bent-over reverse fly in your next block? Hercules logs every set, shows last session's numbers before you lift, and suggests when to add weight.

Get it on Google Play

Dumbbell Bent-Over Reverse Fly variations and alternatives

Sitting supports the torso so your back and legs do less work.

A guided path that keeps your torso supported.

Cables keep tension on the rear delts through the bottom of the rep.

Face Pull

Alternative

Trains the rear delts and upper back with a pulling path toward your face.

Paused Bent-Over Reverse Fly

Harder

A longer pause at the top makes light weights much harder.

Frequently asked questions

What muscles does the bent-over reverse fly work?

It mainly works the rear deltoids, with help from the upper back muscles that pull your shoulder blades together.

How heavy should the dumbbells be?

Lighter than you think. If you have to swing or bend your elbows to finish a rep, go lighter.

Why do I feel it in my lower back?

The lower back holds your hinged position. That is normal, but if it hurts, try the seated version or a chest-supported variation.

Is a reverse fly the same as a rear delt raise?

They are very similar. Both raise the arms out to the sides to train the rear delts, and the names are often used interchangeably.

Hercules tracks every dumbbell bent-over reverse fly you log, shows you last session's numbers before you lift, and flags when your progress stalls.

Get it on Google Play