Back · Horizontal pull

Band Single Arm Low Row

The band single arm low row is a beginner back exercise where you anchor a band near the floor and row it to your hip with one hand. Working one side at a time lets you focus on the lat and mid back, and the staggered stance helps you stay steady without needing any weights.

Also known as: Single arm resistance band row, One arm band low row, Standing single arm band row

Muscle group
Back
Movement pattern
Horizontal pull
Type
Compound
Equipment
Resistance band, Anchor point
Difficulty
Beginner

What muscles does the band single arm low row work?

Primary movers

  • Latissimus dorsi
  • Trapezius (middle)

Assisting muscles

  • Rhomboids
  • Rear deltoid
  • Biceps brachii
  • Brachialis
  • Erector spinae
  • Obliques
  • Forearm flexors

The lats do the main pulling. They drive your elbow back toward your hip, and the low anchor sets a pull that matches the way the lat runs.

The middle trapezius and rhomboids pull your shoulder blade toward your spine at the end of the row. The rear delts help near the top.

The biceps and brachialis bend your elbow, and the forearms hold the band. The obliques and lower back work lightly to keep your torso from twisting.

Because each arm works alone, this is a good way to check for side-to-side differences. The band gets harder as it stretches, so the squeeze at the end of the rep is the hardest part.

How to do the band single arm low row

Setup

  1. 1

    Anchor a resistance band low in front of you, near the floor.

  2. 2

    Hold the band in one hand and step back into a staggered stance with the opposite foot forward.

  3. 3

    Lean your torso slightly forward with a flat back.

  4. 4

    Start with your arm extended toward the anchor and a little tension in the band.

Execution

  1. 1

    Pull the band back toward your hip, driving your elbow close to your side.

  2. 2

    Squeeze your shoulder blade toward your spine.

  3. 3

    Extend your arm slowly, keeping tension in the band.

  4. 4

    Finish all reps on one side, then switch arms.

Common band single arm low row mistakes

Rotating the torso

Twisting to finish the pull takes the work off the lat.

The fix: Keep your hips and shoulders square to the anchor.

Rounding the lower back

Leaning forward with a rounded spine strains the back.

The fix: Keep your chest up and your back flat.

Shrugging the shoulder

Raising the shoulder toward your ear shifts work to the upper trapezius.

The fix: Keep your shoulder down and pull with your elbow.

Letting the band snap forward

The band pulls your arm out and you lose the lengthening phase.

The fix: Control the return slowly until your arm is straight.

How many sets and reps?

GoalSetsRepsLoadRest
Hypertrophy3–412–15Moderate band tension60 s
Endurance2–3 per side15–20Light band30–45 s
Beginner2–3 per side10–12Light band60 s

Use it as a warm-up row, a home back exercise or a finisher after heavier rows. Step further from the anchor to add tension.

Running the band single arm low row in your next block? Hercules logs every set, shows last session's numbers before you lift, and suggests when to add weight.

Get it on Google Play

Band Single Arm Low Row variations and alternatives

Band Rows

Easier

Both arms work at once, which is simpler to set up.

A dumbbell gives a heavier and more steady load.

The same one-arm pull with constant cable tension.

Frequently asked questions

What does the band single arm low row work?

The lats and mid back, with help from the biceps and rear delts.

How do I make it harder?

Step further from the anchor or use a stronger band.

Where should I anchor the band?

Low, near the floor, so you pull up and back toward your hip.

Why train one arm at a time?

It lets you focus on each side and check that both sides work equally.

Hercules tracks every band single arm low row you log, shows you last session's numbers before you lift, and flags when your progress stalls.

Get it on Google Play