Back · Horizontal pull
Cable Single Arm Bent-Over Row
The cable single arm bent-over row is a standing back exercise where you hinge forward, hold a low pulley handle in one hand and row it toward your hip. The cable keeps constant tension on the lats through the whole range, and the one-arm setup lets you train each side of your back on its own.
Also known as: Single arm cable row, One arm cable bent over row, Standing single arm cable row
- Muscle group
- Back
- Movement pattern
- Horizontal pull
- Type
- Compound
- Equipment
- Cable machine, Single handle
- Difficulty
- Beginner
What muscles does the cable single arm bent-over row work?
Primary movers
- Latissimus dorsi
- Trapezius (middle)
Assisting muscles
- Rhomboids
- Upper back
- Rear deltoid
- Biceps brachii
- Brachialis
- Obliques
- Spinal erectors
- Forearm flexors
The lats and middle back do most of the work. They pull your elbow behind your torso and bring your shoulder blade toward your spine.
The rear delt, biceps, brachialis and forearms assist. The obliques and lower back work to keep your torso from rotating toward the cable.
A cable gives steady tension from the stretch to the top, unlike a dumbbell, which is lightest at the bottom of the pull. The one-arm setup lets you match each side.
The hinge and the staggered stance make your core and hips work too, so this is more demanding on balance than a seated row.
How to do the cable single arm bent-over row
Setup
- 1
Set a pulley at the lowest position and attach a single handle.
- 2
Hold the handle in one hand, then step back and stagger your feet.
- 3
Hinge forward with a flat back and rest your free hand on your front thigh.
Execution
- 1
Row the handle toward your hip, driving your elbow back close to your body.
- 2
Squeeze your shoulder blade toward your spine.
- 3
Extend your arm slowly until it is straight.
- 4
Complete all reps on one side, then switch.
Common cable single arm bent-over row mistakes
Twisting the torso to move the weight
Turning shifts the load to your lower back and shortens the pull.
The fix: Keep your hips and shoulders square to the floor.
Rounding the back
A rounded spine under load strains your lower back.
The fix: Keep your chest up and your back flat.
Shrugging the shoulder
Your upper traps take over from the lat.
The fix: Keep your shoulder down and think about driving the elbow back.
Pulling toward the chest
The elbow flares and the lat gets less work.
The fix: Pull toward your hip with the elbow close to your side.
How many sets and reps?
| Goal | Sets | Reps | Load | Rest |
|---|---|---|---|---|
| Hypertrophy | 3–4 | 10–15 | Moderate, slow lowering | 90 s |
| Strength | 4 | 6–10 | Heavy, strict form | 2 min |
| Beginner | 2–3 | 10–12 | Light | 60–90 s |
Use it after heavier rows or as a finisher to balance the two sides. Do all reps on one arm, then switch, and take the same rest for both.
Running the cable single arm bent-over row in your next block? Hercules logs every set, shows last session's numbers before you lift, and suggests when to add weight.
Get it on Google PlayCable Single Arm Bent-Over Row variations and alternatives
Sitting removes the need to hold a hinge.
Single-Arm Dumbbell Row
AlternativeA free-weight one-arm row with support from a bench.
Cable Standing Row
AlternativeA two-arm cable row from a standing position.
Frequently asked questions
What does the cable single arm bent-over row work?
It works the lats and mid back, with help from the rear delts, biceps and core.
Why row with a cable instead of a dumbbell?
A cable keeps tension on the lats through the whole pull, including the bottom of the range.
Where should I pull the handle?
Toward your hip, with the elbow staying close to your body.
How do I keep my torso from twisting?
Stagger your feet, brace your core and keep your hips and shoulders square.
Hercules tracks every cable single arm bent-over row you log, shows you last session's numbers before you lift, and flags when your progress stalls.
Get it on Google Play